Config nyu muna ipv4 nyu >> CLICK Start >> Control Panel
>> Network and Internet >> Network and Sharing Center
>> Change Adapter Settings (nasa upper left screen) then hanapin
nyu Local Area Connection, right click then PROPERTIES hanapin sa ibaba
[Internet Protocol Version 4 (tcp/IPV4) DOUBLE CLICK it, then SET NYU
the FF:
IP ADDRESS: 192.168.1.100
SUBNET MASK: 255.255.255.0
DEFAULT GATEWAY: 192.168.254.1
then click OK...
wait muna kau few minutes....
Tapos Access nyu : 192.168.254.1 sa CHROME if ma open siya....
I reset MODEM nyu tapos restart nyu PC nyu, then try to clear the IPV4 configuration after restart if accessible ba ang GUI nang WIMAX....
If hindi pa din accessible GUI ng WIMAX after clearing the IPV4 configuration, i config nyu ulit tpos UPGRADE nyu WIMAX nyu sa v30 using Multicast tool:
IP ADDRESS: 192.168.1.100
SUBNET MASK: 255.255.255.0
DEFAULT GATEWAY: 192.168.254.1
then click OK...
wait muna kau few minutes....
Tapos Access nyu : 192.168.254.1 sa CHROME if ma open siya....
I reset MODEM nyu tapos restart nyu PC nyu, then try to clear the IPV4 configuration after restart if accessible ba ang GUI nang WIMAX....
If hindi pa din accessible GUI ng WIMAX after clearing the IPV4 configuration, i config nyu ulit tpos UPGRADE nyu WIMAX nyu sa v30 using Multicast tool:
PROCEDURE:
Open Multicast tool
1st. Select Your network card
2nd. Set Nyu Device BM622i
3rd. Select the firmware (.bin) extension
4th. Click Start
Note: That at this moment WALA PANG POWER WIMAX nyu at hndi pa ito naka PLUG SA LAN NYU...
AFTER CLICKING START I UNA NYUNG PLUG ANG [LAN SA PC NYU NEXT, I PLUG ANG WIMAX SA OUTLET]
ITS VERY CLEAR NA MAAUNA MUNANG ISASAK ANG LAN ng WIMAX sa PC before Ito I POWER ON!
MAKIKITANG NYUNG MAGDIDISCO LIGHT ANG WIMAX SIGNAL,wait lang kayo few minutes....
IF NAGSTOP ANG LIGHTS 1,4,5 NG WIMAX IT MEANS SUCCESFULL ANG UPDATE, PWEDE NG I STOP ANG MULTICAST...THEN UNPLUG/PLUG YOUR MODEM...
IF PASTOP-STOP ANG PROCESS TAPOS HUMIHINTO ANG PAGDIDISCO LIGHT LNG WIMAX, FAILED ANG PROCESS RETRY ULIT.
Credits to sir FrancisRen
Open Multicast tool
1st. Select Your network card
2nd. Set Nyu Device BM622i
3rd. Select the firmware (.bin) extension
4th. Click Start
Note: That at this moment WALA PANG POWER WIMAX nyu at hndi pa ito naka PLUG SA LAN NYU...
AFTER CLICKING START I UNA NYUNG PLUG ANG [LAN SA PC NYU NEXT, I PLUG ANG WIMAX SA OUTLET]
ITS VERY CLEAR NA MAAUNA MUNANG ISASAK ANG LAN ng WIMAX sa PC before Ito I POWER ON!
MAKIKITANG NYUNG MAGDIDISCO LIGHT ANG WIMAX SIGNAL,wait lang kayo few minutes....
IF NAGSTOP ANG LIGHTS 1,4,5 NG WIMAX IT MEANS SUCCESFULL ANG UPDATE, PWEDE NG I STOP ANG MULTICAST...THEN UNPLUG/PLUG YOUR MODEM...
IF PASTOP-STOP ANG PROCESS TAPOS HUMIHINTO ANG PAGDIDISCO LIGHT LNG WIMAX, FAILED ANG PROCESS RETRY ULIT.
Credits to sir FrancisRen
